In short
- For a fleet that relies on negative effects, check accuracy against the resistance of the intended target.
- Accuracy and resistance are values, not percentages. Neither 100 nor 250 is a cutoff in the ordinary check.
- Damage mitigation reduces incoming damage. Resistance reduces the chance of checked enemy effects.
- Read an effect's own conditions too. Battle effects: who applies what lists them.
Scheme
The horizontal axis is resistance minus accuracy. At equal stats the chance is about 93.7%; resistance 50 above accuracy gives 50%. The graph covers this check alone.
How it works
- Other sources and mode rules
- Admirals can add both stats. Clan: what it gives your fleet covers clan-level and Mothership research bonuses. Sector Warfront disables personal technology bonuses and limits the gains from officers, modules, drones, sets and admirals.
- Why later enemies resist more
- Campaign and other PvE enemies gain extra accuracy and resistance as stages rise. Use the comparison window to see the enemy’s values.
- Greatly increased accuracy
- When an ability says “with greatly increased accuracy”, it adds 100 accuracy for that check; it is still a roll. If resistance is 100 above the applier’s ordinary accuracy, the check is about 93.7%. The Marked effect skips this check. Battle effects: who applies what gives its rules.
- Which squadron supplies each stat
- The squadron applying the effect supplies accuracy. The squadron receiving it supplies resistance. For defense, compare your resistance with enemy accuracy; for an attack, compare your accuracy with enemy resistance. The same accuracy check also decides whether enemy abilities remove your positive effects.
- The curve
The ordinary check uses the difference between the two stats. Equal values give about 93.7%, while resistance 50 above accuracy gives 50%.
Chance, % = 100 × [0.5 + arctan(0.1 × (accuracy − resistance + 50)) ÷ π]
Increasing resistance has its largest effect near the steep part of the curve. Farther along either end, the same extra value changes the chance by less.
- Should resistance exceed 100 or 250?
Those values have no special cutoff. What matters is how far resistance exceeds the applying squadron's accuracy.
With resistance 100 above accuracy, the check succeeds about 6.3% of the time. At 250 above accuracy it succeeds about 1.6%. A higher enemy accuracy changes both examples.
- The check and the full effect
- Some effects have their own application chance before the accuracy check, and ability conditions or blocking can stop the effect. For the guarantee question, see Myths and checks.
- Where accuracy and resistance come from
Matching bonuses from officers and the stats on equipped modules add to these values. Some completed sets add 50 accuracy or resistance. Module sets lists them.
Technologies can add bonuses for a ship type or the whole fleet. In Magnetar, temporary boosters from applied cards can add both stats.
- Effects during battle
- The effect «Increased Accuracy» adds 50 accuracy; «Increased Resistance» adds 50 resistance; «Reduced Resistance» subtracts 50 resistance. These change the values used by later accuracy checks.
- Damage mitigation is a different stat
- Damage mitigation changes how much incoming damage is kept. Resistance belongs to the accuracy check. Raising resistance does not replace protection against weapon damage.
- Armor penetration has a separate limit
Additional armor penetration adds to the damage multiplier for the weapon type and target class. Armor effects also change that part of the multiplier.
The squadron’s additional armor penetration, including any extra for this hit, counts up to +99%. The whole type-plus-penetration multiplier is capped at 2×. Other bonuses and defenses apply afterward; this is not a final-damage limit.
Damage types and armor penetration gives the weapon multipliers and target restrictions.
An example
- Change accuracy, keep the target
- An applying squadron has 100 accuracy and its target has 150 resistance: the check succeeds with 50% probability. With «Increased Accuracy», the applying squadron reaches 150 accuracy. The stats are now equal, so the chance is about 93.7%. The effect's own probability and other conditions still apply.
Where it matters
- Before changing equipment
- Use How to build a fleet to check which effects the fleet needs and which enemy should receive them. Compare the relevant squadrons before trading attack or hull bonuses for accuracy or resistance.
- Read the enemy
- The accuracy and resistance explanations in the comparison window use the same formula for the selected squadrons. This is a pre-battle estimate of the accuracy roll; separate effect probabilities, battle effects, boosters and greatly increased accuracy can change the full result. The in-game explanation describes a narrower set of uses than the check actually has.
- Check the effect
- Battle effects: who applies what lists the effects, their application and blocking rules.
Game version 1.46.2.
Found a mistake or something missing? Tell us